diff --git a/documentation/SubGHzRemoteProg.md b/documentation/SubGHzRemoteProg.md
new file mode 100644
index 000000000..5f453806e
--- /dev/null
+++ b/documentation/SubGHzRemoteProg.md
@@ -0,0 +1,60 @@
+# How to use Flipper as a new SubGHz remote (not clone of original remote)
+
+## Somfy Telis
+
+1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> Somfy Telis 433Mhz
+2. Open your new remote file
+3. Long press (hold) the ‘Prog’ button on a remote that is already registered to the device, until the blinds move shortly up and down.
+4. Press and hold the ‘Prog’ button on the flipper (Left Arrow), until the blinds move shortly up and down again.
+5. Done?
+
+## BFT Mitto 
+
+1. Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> BFT Mitto 433Mhz
+2. Open your new remote file
+3. You need to be in minimum 3 meters to receiver
+4. Original Remote: Press hidden button on back of remote with a pin or paper clip OR press Button 1 & 2 together until remote LED lights.
+5. Original Remote: Momentarily press button that opens device
+6. Long press (Right Arrow) - (0xF button - Btn:F) on Flipper for like 3-5 sec
+7. Done?
+
+## Nice Flor S
+
+- Create new remote with randomly generated serial: Go to SubGHz -> Add Manually -> Nice FloR-S 433Mhz
+- Open your new remote file
+
+### Coding using an existing remote
+To enter the code of a new remote control without using your receiver, you will need
+an authorised remote control (note: the first remote control must always be entered
+using the receiver key). Now, with the two remote controls (your already coded
+remote, and your new remote), which we shall call NEW (the one whose code we want
+to enter) and OLD (the authorised one), position yourself within 3m of the gate/garage
+receiver and then:
+1. Press and hold the `Send` button on the flipper for at least 5 seconds and then
+release.
+2. Press the button on the already programmed remote 3 times slowly.
+3. Press the `Send` button on the flipper slowly and then release.
+
+### Coding directly to your receiver
+Your new remote will program to your receiver as per your original remote
+instructions, so please refer to your manual. But for a typical NICE FLOX2R Receiver,
+the programming procedure is as follows:
+1. Press the learning button on your receiver for 1-2 seconds. The LED will turn on
+for 5 seconds. Within 5 seconds, complete the next step.
+2. Press a `Send` button on your flipper until the LED on your receiver turns off.
+3. Release the remote button and wait for 2 seconds.
+4. Press the `Send` button on your flipper again. The LED on your receiver
+will now flash 3 times. This indicates that your remote has been successfully
+coded. If this does not happen, repeat the whole procedure from the
+beginning, and try again.
+5. Wait 5 seconds. Press the button on your new remote to test if it opens your
+garage/gate.
+
+
+#### Follow links below to find more detailed instructions!!!
+
+#### Materials used:
+- [Somfy Telis](https://pushstack.wordpress.com/somfy-rts-protocol/)
+- [BFT Mitto](https://www.retroremotes.com.au/wp-content/uploads/2017/03/BFT-MITTO-2-4-19-6-17.pdf)
+- [NICE FLOX2R Receiver Programming](https://apollogateopeners.com/store/pdf/apollo-flor-s-receiver-programming-guide.pdf)
+- [Nice Flor S Programming](https://motepro.com.au/Instructions/Nice.pdf)
\ No newline at end of file