Previously all HackRF devices were hardcoded as "HackRF One" regardless
of actual hardware variant. Now parses the Board ID line from hackrf_info
to correctly identify HackRF Pro, HackRF One, and other variants.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
rtl_test opens the USB device during probing. After killing the
process, the kernel may not release the USB interface immediately.
dump1090 then fails with usb_claim_interface error -6. Add a 0.5s
delay after probe cleanup to allow the kernel to fully release the
device before the actual decoder opens it.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
rtl_test -t often exits non-zero after finding a device (e.g.
"No E4000 tuner found, aborting" with R820T tuners). The return
code fallback was firing even when the "Found N device(s)" success
message had already been matched. Track device_found separately
and only use return code as fallback when no success was seen.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
The success check ('Found' in line and 'device' in line) matched
"No supported devices found" since both keywords appear. Add a
pre-check for negative device messages, a return code fallback,
and a clearer error message.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Move adsb_active_device/sdr_type assignment to immediately after
claim_sdr_device so stop_adsb() can always release the device, even
during startup. Sync sdr_type_str after SDRType fallback to prevent
claim/release key mismatch. Clear active device on all error paths.
Replace blind 3s sleep for dump1090 readiness with port-polling loop
(100ms intervals, 3s max). Replace subprocess.run() in rtl_test probe
with Popen + select-based early termination on success/error detection.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add .gitignore entry for data/subghz/captures/ to prevent large
IQ recording files from being committed.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
When an external process (or stale handle from a crash) holds an SDR
device, claim_sdr_device() registry check passes but rtl_fm fails with
usb_claim_interface error -6. This adds a quick rtl_test probe inside
claim_sdr_device() so all modes get a clear error message before the
decoder pipeline is launched.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Set DYLD_LIBRARY_PATH and SOAPY_SDR_ROOT environment variables when
running SoapySDRUtil on macOS so Homebrew-installed modules (HackRF,
LimeSDR, etc.) are properly detected.
Fixes#77
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
Adds support for SDRPlay RSP devices (RSPdx, RSP1A, RSPduo, etc.)
through the SoapySDR interface. Closes#44.
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
Previously, RTL-SDR devices from SoapySDR were unconditionally skipped,
even if native rtl_test wasn't available. Now:
- Native detection runs first for RTL-SDR and HackRF
- SoapySDR only skips device types that were already found natively
- If native tools aren't available, SoapySDR detection is used as fallback
This fixes the issue where users with only SoapySDR installed couldn't
see their RTL-SDR or HackRF devices.
🤖 Generated with [Claude Code](https://claude.com/claude-code)
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
Airspy support:
- Add AIRSPY to SDRType enum and driver mappings
- Create AirspyCommandBuilder using SoapySDR tools (rx_fm, readsb, rtl_433)
- Register in SDRFactory and add to hardware type dropdown
- Supports Airspy R2/Mini (24MHz-1.8GHz) and HF+ devices
GPS coordinate persistence:
- Save observer location to localStorage when manually entered or via geolocation
- Restore saved coordinates on page load in both index.html and adsb_dashboard.html
- Coordinates are shared between both pages
🤖 Generated with [Claude Code](https://claude.com/claude-code)
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Add GPS dongle support with NMEA parsing (utils/gps.py, routes/gps.py)
- Add GPS device selector to ADS-B and Satellite observer location sections
- Add GPS dongle option to ADS-B dashboard
- Fix Python 3.7/3.8 compatibility by adding 'from __future__ import annotations'
to all SDR module files (fixes TypeError: 'type' object is not subscriptable)
- Add pyserial to requirements.txt
- Update README with GPS dongle documentation and troubleshooting
🤖 Generated with [Claude Code](https://claude.com/claude-code)
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
