Dispatch observer-location-changed event from settings manager and
listen for it in APRS mode so manual location saves propagate to
the map and distance calculations. Also refresh ObserverLocation in
initAprsMap() to catch changes between page load and first map use.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add WiFi Locate mode for locating access points by BSSID with real-time
signal meter, distance estimation, RSSI history chart, and audio
proximity tones. Includes hand-off from WiFi detail drawer, environment
presets (Free Space/Outdoor/Indoor), and signal-lost detection.
Also includes:
- Mobile navigation reorganized into labeled groups (SIG/TRK/SPC/WIFI/INTEL/SYS)
- flask-limiter made optional with graceful degradation
- Fix radiosonde setup missing semver Python dependency
- Documentation updates (FEATURES, USAGE, UI_GUIDE, GitHub Pages site)
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Fix XSS: escape ASCII output in innerHTML via escapeHtml()
- Fix deadlock: use put_nowait() for queue ops under ook_lock
- Fix SSE leak: add ook to moduleDestroyMap so switching modes
closes the EventSource
- Fix RSSI: explicit null check preserves valid zero values in
JSON export
- Add frame cap: trim oldest frames at 5000 to prevent unbounded
memory growth on busy bands
- Validate timing params: wrap int() casts in try/except, return
400 instead of 500 on invalid input
- Fix PWM hint: correct to short=0/long=1 matching rtl_433
OOK_PWM convention (UI, JS hints, and cheat sheet)
- Fix inversion docstring: clarify fallback only applies when
primary hex parse fails, not for valid decoded frames
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Covers identifying modulation type (PWM/PPM/Manchester), finding
pulse timing via rtl_433 -A, common ISM frequencies and timings,
and troubleshooting tips for tolerance and bit order.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Full-stack meteor scatter monitoring mode that captures IQ data from
an RTL-SDR, computes FFT waterfall frames via WebSocket, and runs a
real-time detection engine to identify transient VHF reflections from
meteor ionization trails (e.g. GRAVES radar at 143.050 MHz).
Backend: MeteorDetector with EMA noise floor, SNR threshold state
machine (IDLE/DETECTING/ACTIVE/COOLDOWN), hysteresis, and CSV/JSON
export. WebSocket at /ws/meteor for binary waterfall frames, SSE at
/meteor/stream for detection events and stats.
Frontend: spectrum + waterfall + timeline canvases, event table with
SNR/duration/confidence, stats strip, turbo colour LUT. Uses shared
SDR device selection panel with conflict tracking.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Add missing setThemePreference() and setAnimationsEnabled() functions
to settings-manager.js; sync theme/animations dropdowns in _updateUI
- Fix base.html toggleTheme() saving to wrong localStorage key ('theme'
instead of 'intercept-theme'), causing theme not to persist in ADS-B
and AIS dashboards; also sync button icon and persist to server
- Add [data-theme="light"] CSS variable overrides to adsb_dashboard.css
and ais_dashboard.css so the dashboards respond to light theme
- Fix GPS sky view canvas (gps.js) to read grid/label colours from CSS
variables instead of hardcoded dark hex values; add MutationObserver
to redraw immediately on theme change
- Fix satellite_dashboard.html polar plot functions to read background,
accent and text colours from CSS variables
Closes#139
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Replace IBM Plex Mono, Space Mono, and JetBrains Mono with Roboto
Condensed across all CSS variables, inline styles, canvas ctx.font
references, and Google Fonts CDN links. Updates 28 files covering
templates, stylesheets, and JS modules for consistent typography.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
- Add VDL2 to syncModeUI setter map and allModes array in agents.js
so agent state sync works for VDL2
- Fix dashboard bottom gap by using flex layout on body instead of
hardcoded calc(100dvh - 160px) height
- Match source stat font-size to other stats (14px) for consistent
strip sizing
- Add left-sidebars wrapper, VDL2 agent mode support, mutual sidebar
collapse, and ACARS/VDL2 modeNames in index.html
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add .gitignore entry for data/subghz/captures/ to prevent large
IQ recording files from being committed.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Resolve conflicts keeping local GSM tools in kill_all() process list
and weather satellite config settings while merging upstream changes
including GSM spy removal, DMR fixes, USB device probe, APRS crash
fix, and cross-module frequency routing.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Remove all GSM cellular intelligence features including tower scanning,
signal monitoring, rogue detection, crowd density analysis, and
OpenCellID integration across routes, templates, utils, tests, and
build configuration.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Parse tshark GSM field values with int(value, 0) instead of int(value)
to auto-detect hex 0x-prefixed output (e.g. 0x039e for TMSI/LAC/CID).
Without this, every tshark line with hex values fails to parse, causing
0 devices to be captured during monitoring.
Also add API Keys tab to Settings modal for configuring OpenCellID key
via the UI (in addition to env var), with status display and usage bar.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Merges upstream changes into fork while preserving weather satellite
(NOAA APT/Meteor LRPT via SatDump), rtlamr, multi-arch build, and
decoder console features from our branch.
Co-Authored-By: Claude Opus 4.6 <noreply@anthropic.com>
Add defensive typeof checks before referencing the Updater global in
loadUpdateStatus() and checkForUpdatesManual() so the settings panel
shows a helpful message instead of crashing. Also swap script load
order so updater.js loads before settings-manager.js.
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
The sweep loop's WiFi/BT/RF scan processing had unprotected
timeline_manager.add_observation() calls that could crash an entire
scan iteration, silently preventing all device events from reaching
the frontend. Additionally, scan interval timestamps were only updated
at the end of processing, causing tight retry loops on persistent errors.
- Wrap timeline observation calls in try/except for all three protocols
- Move last_*_scan timestamp updates immediately after scan completes
- Add per-device try/except so one bad device doesn't block others
- Emit sweep_progress after WiFi scan for real-time status visibility
- Log warning when WiFi scan returns 0 networks for easier diagnosis
- Add known_device and score_modifier fields to correlation engine
- Add TSCM scheduling, cases, known devices, and advanced WiFi indicators
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Add help modal system with keyboard shortcuts reference
- Add Main Dashboard button in navigation bar
- Make settings modal accessible from all dashboards
- Dashboard CSS improvements and consistency fixes
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
Features:
- Display connected clients for access points in detail drawer
- Real-time client updates via SSE streaming
- Client cards show MAC, vendor, RSSI, probed SSIDs, and last seen
- Count badge in Connected Clients header
Other changes:
- Updated aircraft database
- CSS and template refinements
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
Issues fixed:
- #113: Display RTL-SDR serial numbers in device selector
- #112: Kill all processes now stops Bluetooth scans
- #111: BLE device list no longer overflows container bounds
- #109: WiFi scanner panels maintain minimum width (no more "imploding")
- #108: Radar device hover no longer causes violent shaking
- #106: "Use GPS" button now uses gpsd for USB GPS devices
- #105: Meter trend text no longer overlaps adjacent columns
- #104: dump1090 errors now provide specific troubleshooting guidance
Changes:
- app.py: Add Bluetooth cleanup to /killall endpoint
- routes/adsb.py: Parse dump1090 stderr for specific error messages
- templates/index.html: Show SDR serial numbers in device dropdown
- static/css/index.css: Fix WiFi/BT panel layouts with proper min-width
- static/css/components/signal-cards.css: Fix meter grid overflow
- static/css/components/proximity-viz.css: Fix radar hover transform
- static/css/settings.css: Add GPS detection spinner
- static/js/components/proximity-radar.js: Add invisible hit areas
- static/js/core/settings-manager.js: Use gpsd before browser geolocation
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Add DopplerTracker class using skyfield for satellite tracking
- Calculate and apply Doppler shift correction (up to ±3.5 kHz at 145.800 MHz)
- Background thread monitors shift and retunes rtl_fm when >500 Hz drift
- New /sstv/doppler endpoint for real-time Doppler info
- Start endpoint accepts latitude/longitude for automatic tracking
Also:
- Add slowrx installation to setup.sh (source build for macOS, apt for Debian)
- Sync observer location to dashboard-specific localStorage keys
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Fix GPS button not working (pass button element to handler)
- Hide output element in SSTV mode to allow panels to fill space
- Add explicit height rules for SSTV panels to expand vertically
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Add Location tab to settings modal with lat/lon inputs
- Add GPS detection button for auto-location
- Update SSTV to use saved location for ISS pass predictions
- Fix SSTV panels to use full screen width (remove max-width constraint)
- Improve ISS pass messages to guide users to location settings
- Add checked/last_check fields to update status response
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Check for new releases from GitHub API with 6-hour cache
- Show toast notification when updates are available
- Add Updates tab in settings for manual checks and preferences
- Support git-based updates with stash handling for local changes
- Persist dismissed versions to avoid repeated notifications
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Add Settings.registerMap() to register maps for tile updates
- Add Settings.createTileLayer() to create tile layers from settings
- Update _updateMapTiles() to use registered maps
- Expose all maps to window object for settings manager access
- All dashboards now use Settings manager when available
- Tile provider changes in settings now apply immediately to all maps
- Use Fastly CDN for CARTO tiles (more reliable)
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
The {r} retina parameter was causing CARTO to return light/gray tiles
instead of dark tiles. Removed {r} from all tile layer URLs.
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
- Fix traceroute button in Meshtastic popups using event delegation
instead of inline onclick handlers (more reliable with Leaflet)
- Update all maps to use dark CARTO tiles for consistency:
- ADS-B dashboard radar map
- AIS dashboard vessel map
- Satellite dashboard ground map
- APRS map
- Satellite ground track map in main UI
- Change settings manager default tile provider to cartodb_dark
Co-Authored-By: Claude Opus 4.5 <noreply@anthropic.com>
